Explanations of Test and Data Display

[Table of Contents] [Previous Page] [Next Page]

9. EXPLANATIONS OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

When the test mode is finished, the Foot Controller performs centering. At the time the test mode is finished, if anyone remains on the Foot Controller or on the CAUTION MAT, this can cause injury. To avoid injury, be very careful when finishing the test mode.

In the case where multiple machines are linked for communication play, if any one of the machines enters the test mode, all other linked machines enter the test mode automatically. Therefore, if any one of the machines is in play, be very careful so as not to enter the test mode.

TABLE 9 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS

INSTALLATION OF MACHINE When the machine is installed, perform the following:
1. Check to see that each setting is as per standard setting made at the time of shipment.
2. In the INPUT TEST mode, check each SW and VR.
3. In the OUTPUT TEST mode, check each of lamps.
4. In the SELF-TEST mode, check ICs on the IC Board.
9-9, 9-10

9-5
9-6
9-3, 9-4

MEMORY Choose MEMORY TEST in the MENU mode to allow the MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked. 9-3, 9-4

PERIODIC SERVICING Periodically perform the following:
1. MEMORY TEST
2. Ascertain each setting.
3. In the INPUT TEST mode, test the CONTROL device
4. In the OUTPUT TEST mode, check each of lamps.

9-3, 9-4
9-9, 9-10
9-5
9-6

CONTROL SYSTEM 1. In the INPUT TEST mode, check each SW and VR.
2. Adjust or replace each SW and VR.
3. If the problem can not be solved yet, check the CONTROL's moves. 9-5
9-10, 10

MONITOR In the MONITOR ADJUSTMENT mode, check to see if the PROJECTOR adjustment is appropriately made. 9-8
12

IC BOARD 1. MEMORY TEST
2. In the SOUND TEST mode, check the sound related ROMs. 9-3
9-7

DATA CHECK Check such data as game play time and histogram to adjust the difficulty level, etc 9-12

ITEMS	DESCRIPTION	SECTIONS

INSTALLATION OF MACHINE	When the machine is installed, perform the following: 1. Check to see that each setting is as per standard setting made at the time of shipment. 2. In the INPUT TEST mode, check each SW and VR. 3. In the OUTPUT TEST mode, check each of lamps. 4. In the SELF-TEST mode, check ICs on the IC Board.	9-9, 9-10 9-5 9-6 9-3, 9-4
MEMORY	Choose MEMORY TEST in the MENU mode to allow the MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.	9-3, 9-4
PERIODIC SERVICING	Periodically perform the following: 1. MEMORY TEST 2. Ascertain each setting. 3. In the INPUT TEST mode, test the CONTROL device 4. In the OUTPUT TEST mode, check each of lamps.	9-3, 9-4 9-9, 9-10 9-5 9-6
CONTROL SYSTEM	1. In the INPUT TEST mode, check each SW and VR. 2. Adjust or replace each SW and VR. 3. If the problem can not be solved yet, check the CONTROL's moves.	9-5 9-10, 10
MONITOR	In the MONITOR ADJUSTMENT mode, check to see if the PROJECTOR adjustment is appropriately made.	9-8 12
IC BOARD	1. MEMORY TEST 2. In the SOUND TEST mode, check the sound related ROMs.	9-3 9-7
DATA CHECK	Check such data as game play time and histogram to adjust the difficulty level, etc	9-12