12 - 3 TOSHIBA MONITOR

NOTE: THIS PAGE CONTAINS MANY GRAPHICSAND MAY TAKE A MINUTE OR TWO TO LOAD. IF YOU DO NOT HAVE A TOSHIBAMONITOR, YOU MAY PRESS THE STOP BUTTON ON YOUR BROWSER AND THENFOLLOW ONE OF THE LINKS ABOVE TO CONTINUE.

Do not touch places other than those specified.Touching places not specified can cause an electric shock or shortcircuit accident.

Do not press undesignated key. Pressing any undesignatedkey can cause malfunction and adjustment fault. Should the keybe pressed by mistake, turn power off and turn it back on again.

TOSHIBA PROJECTOR CONTROL PANEL

TOSHIBA PROJECTOR has two different types, i.e., one equipped with the Control Panel and the other without the Control Panel. When adjusting, be sure to confirm the type used.

STATIC CONVERGENCE ADJUSTMENT (With the Control Panel)

During adjustment, should the screen image beabnormally disfigured due to static electricity and other causes,do not have adjustment status stored, and be sure to turn poweroff.

Operate the Remote Control towards the PTV screen. If directedother than to the PTV screen, the Remote Control does not function.Unlessthe CONV ADJ SW is ON, remote control operation is not acceptable.At the time of shipment, the SW is set to ON. If remote controlis not accepted, check status of this SW.

Direct the remote control towards the PTV screen and keep theTest Key pressed down for approximately 3 seconds. The adjustmentmode should appear on the screen and the screen turns into thegreen test pattern.

On the screen, the cross pattern and the square frame linewill be projected. However, due to the TV mask, the up/down linescannot be seen.

When initially installing the machine, or when the installationposition is changed, check to see if the Test Pattern is in thecentral, well balanced position. If deviated, adjust the greenposition by using the Adjust Key "up/down/left/right"in the manner so as to improve the balance (L&R, and T&Bare approximately equal as shown).

In the normal usage, with green as reference color, red andblue are adjusted. Therefore, skip the above procedure.

Press the R Key of the remote control. The red pattern togetherwith the green pattern are displayed on the screen. At this time,the frame color turns into red.

By operating the Adjust Key of the remote control "up/down/left/right",have the center red match with that of green. When red color issuperimposed on green color, it seems to be yellow.

Press the B Key of remote control. The blue test pattern isadded to the display on the screen. At this time, the frame colorturns into blue.

By operating the Adjust key of the remote control "up/down/left/right",have the center of the blue match with that of yellow. When bluecolor is superimposed on yellow color, it seems to be white.

By pressing the WRITING KEY, have the adjustment status stored.After it has been stored, the Adjustment Mode is exited automatically,and the normal mode returns. If the Test Key is pressed down forapproximately 3 seconds without having the adjustment status stored,pre adjustment status will remain.

The R.G.B. Keys have screen display color change functions.Pressing the key of the color presently shown on the screen causesthe color to disappear, therefore, for adjustment, press the keyagain.

ADJUSTMENT OF TOSHIBA PROJECTOR (THE TYPE WITHOUT CONTROL PANEL)

The Remote Control is used for adjustment of the type without Control Panel. When adjusting the Projector, direct the Remote Control's light emitting portion towards the Projector Screen.

REMOTE CONTROL BUTTONS

AUTOMATIC COLOR MATCHING

The Projector may be subject to color deviations affected by earth magnetism, the building's steel frames, etc. When the Projector is initially installed of the Projector's installation position is changed, have the color matching performed automatically.

Keep pressing the p button (red) for approximately 3 seconds to have the ensuing movements performed automatically.When the green cross pattern movements are finished, similar detection is performed sequentially in order of red and then blue cross movements. After detecting by green, red and blue cross movements, the game mode returns with the color deviation status being corrected

Although very rarely, the TRY AGAIN error display in red may appear. At this time, press the P button (red) for approximately 3 seconds. Even after the above operation is repeated, if the error condition still exists, then display shifts to PLEASE ADJ. In this Case, the auto color matching function can not be used. Contact the place of contact herein stated or where the product was purchased from.

If the automatic color matching indicates an error, color matching can manually be performed. Refer to CONVERGENCE ADJUSTMENT (manual color matching).

ADJUSTING THE ON-SCREEN CONTRAST

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary. Changing the CONTRAST causes the light and shade of the on-screen images to be changed.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure "2" and press the SET BUTTON.

To continue adjusting other menu items, repeat procedure "2~4"

Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will prevail when the power is turned ON the next time.

ADJUSTING THE ON-SCREEN BRIGHTNESS

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary. Changing the BRIGHTNESS causes the light and shade of the on-screen images to be changed.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure "2" and press the SET BUTTON.

To continue adjusting other menu items, repeat procedure "2~4"

Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will prevail when the power is turned ON the next time.

ADJUSTING THE ON-SCREEN CONTRAST

Although the on-screen display position (H. POSI, V. POSI) has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure "2" and press the SET BUTTON.

To continue adjusting other menu items, repeat procedure "2~4"

Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will prevail when the power is turned ON the next time.

ADJUSTING THE SCREEN SIZE

Although the on-screen size (H. SIZE, V. SIZE) has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure and press the SET BUTTON.

To continue adjusting other menu items, repeat procedure "2~4"

Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will prevail when the power is turned ON the next time.

CONVERGENCE ADJUSTMENT (manual color matching)

To avoid circuitry malfunctioning due to electricalload increase, never utilize CONVERGENCE ADJUSTMENT (Line ConvergenceAdjustment in particular) for adjusting screen size changes.

There is no means to restore the Convergence Adjustmentdata once stored, to its original state. To avoid changing thescreen size by erroneously using convergence adjustment, do notperform the green Line Convergence Adjustment.

As such, be sure to perform the adjustment work from this page onward by the Technical staff and the location's maintenance Personnel who are well versed in such adjustment work. In the Static Convergence Adjustments, if satisfactory adjustments can not be performed, do not make another convergence adjustment inadvertently. Contact the office herein stated or where the product was purchased from.To avoid making the adjustment work ineffective, do not press the RESET button during adjustment.

To discontinue adjustment work, keep pressingthe TEST button for approximately 3 seconds at the stage beforestoring the adjustment data by pressing the WRITING button.

Should the screen be abnormally disturbed by noise due tostatic electricity, etc., turn the power off without storing theadjustment data.

Pressing the "up or down" PIC-ADJ button in theConvergence Adjustment Mode status will display the AdjustmentMenu as this is the one applied at the factory.

Adjusting this menu causes the Customer's adjustment rangeto be deviated.

Should the menu shown right be displayed by mistake, firstchoose EXIT by using either "up or down" PIC-ADJ buttonand then press the SET button.

STATIC CONVERGENCE ADJUSTMENT

In the static convergence adjustment, each of red and blueimages is comprehensively moved to and superimposed on the greencolor. If automatic color matching function is not sufficientlysatisfactory, perform this adjustment. Be sure to perform automaticcolor matching before starting the above adjustment.

When either of "2" "4" COLOR SELECT buttons(R,B) is pressed, if the color desired to be adjusted disappears,press that particular button again. For example, if the red colorneeds to be adjusted again at the stage of "4" the Rbutton need to be pressed twice.

POINT CONVERGENCE ADJUSTMENT

In the POINT CONVERGENCE adjustment, each of red, green, and blue images is partially moved for color matching. The adjustment may be necessary when the Game Board is replaced or changed, or screen size is changed. Be sure to perform automatic color matching before starting.

NOTE 1:

When the MODE button is pressed, the adjustment modes will circulate as follows:

NOTE 2:

When either of the COLOR SELECT buttons (R, B) is pressed, if the desired color to be adjusted is erased, press that particular button again.

NOTE 3:

By repeatedly pressing the SELECT button, only the Projector's TEST pattern screen and the screen superimposing the Game Board Test pattern can be alternately displayed.

LINE CONVERGENCE ADJUSTMENT

In the LINE CONVERGENCE adjustment, the adjustment point of the column line (vertical) or row line (horizontal) is comprehensively moved for color matching.It is convenient to utilize this adjustment when color of the column line row line is uniformly deviated.

NOTE 1:

When the MODE button is repeatedly pressed, the adjustment modes will circulate as follows:

NOTE 2:

When either of the COLOR SELECT buttons (R, B) is pressed, if the desired color to be adjusted is erased, press that particular button again.