TROUBLESHOOTING

[Previous Page] [Next Page] [Table of Contents]

12.TROUBLESHOOTING

Should trouble occur, first check connector connections.

PROBLEMS

CAUSE

COUNTERMEASURES

With Main SW ON, no activation
Power is not supplied.

Power Supply/Voltage is not correct.

AC Main fuse causes the power to be cut off due to momentary overload.

Plug in correctly.

Make sure that power supply/voltage is correct.

Check fuse. Remove the cause of overload and replace fuse.

Irregular sound is emitted from the Rear Base
Poor Mesh of mechanism gear inside Rear Base

Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in.

Adjust the gear mesh.

Apply greasing or eliminate extraneous matter.

During Game, no bike body reaction and irregular functioning. Game start does not unlock bike.
POWER ON check is not satisfactory.

Poor connection or malfunctioning of Motor Drive BD.

Overheat of Motor.

1.> Redo power input and complete POWER ON check.

2.> Perform Drive BD test.

3.> Check for connection between motor driver, Driver BD and Game BD.

Wait a while turn power back on.

The color of the image on monitor screen is incorrect. Connector connections are defective. Check the connection for the RGB and SYNC connectors of the monitor TERMINAL BD and VPM BUFFER BD.

The image on PTV screen has color deviation. Affected by magnetic field of installation location. Make CONVERGENCE adjustment. (see section 9)

No sound is emitted.
Sound volume adjustment is not appropriate.

Sound BD and speaker are malfunctioning.

Adjust sound volume. (see section 6)

Perform sound test to find and replace defective parts. (see section 6)

Controller operation is not satisfactory.
Due to environmental changes, etc., sighting became inappropriate.

Micro switch malfunctioning.

Sensor BD malfunctioning

Perform sighting adjustment in the TEST MODE. (see section 6)

Replace the micro switch. (see section 7)

Replace the Sensor BD. (see section 7)

Bike Body is not locked Wing Bolts for maintenace are not removed. Remove wing bolts.

Bike Body centering is not correct.
V.R. setting fault.

V.R. deviation or malfunctioning.

Perform V.R. setting

Adjust or replace V.R.

The Fluorescent lamp does not light up. The Fluorescent tube is burnt out. Replace the Fluorescent tube. (see section 10)

PROBLEMS	CAUSE	COUNTERMEASURES
With Main SW ON, no activation	Power is not supplied. Power Supply/Voltage is not correct. AC Main fuse causes the power to be cut off due to momentary overload.	Plug in correctly. Make sure that power supply/voltage is correct. Check fuse. Remove the cause of overload and replace fuse.
Irregular sound is emitted from the Rear Base	Poor Mesh of mechanism gear inside Rear Base Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in.	Adjust the gear mesh. Apply greasing or eliminate extraneous matter.
During Game, no bike body reaction and irregular functioning. Game start does not unlock bike.	POWER ON check is not satisfactory. Poor connection or malfunctioning of Motor Drive BD. Overheat of Motor.	1.> Redo power input and complete POWER ON check. 2.> Perform Drive BD test. 3.> Check for connection between motor driver, Driver BD and Game BD. Wait a while turn power back on.
The color of the image on monitor screen is incorrect.	Connector connections are defective.	Check the connection for the RGB and SYNC connectors of the monitor TERMINAL BD and VPM BUFFER BD.
The image on PTV screen has color deviation.	Affected by magnetic field of installation location.	Make CONVERGENCE adjustment. (see section 9)
No sound is emitted.	Sound volume adjustment is not appropriate. Sound BD and speaker are malfunctioning.	Adjust sound volume. (see section 6) Perform sound test to find and replace defective parts. (see section 6)
Controller operation is not satisfactory.	Due to environmental changes, etc., sighting became inappropriate. Micro switch malfunctioning. Sensor BD malfunctioning	Perform sighting adjustment in the TEST MODE. (see section 6) Replace the micro switch. (see section 7) Replace the Sensor BD. (see section 7)
Bike Body is not locked	Wing Bolts for maintenace are not removed.	Remove wing bolts.
Bike Body centering is not correct.	V.R. setting fault. V.R. deviation or malfunctioning.	Perform V.R. setting Adjust or replace V.R.
The Fluorescent lamp does not light up.	The Fluorescent tube is burnt out.	Replace the Fluorescent tube. (see section 10)