[Previous page][Next page][Tableof Contents]

12 - 3 TOSHIBA MONITOR

NOTE: THIS PAGE CONTAINS MANY GRAPHICS AND MAYTAKE A MINUTE OR TWO TO LOAD. IF YOU DO NOT HAVE A TOSHIBA MONITOR, YOUMAY PRESS THE STOP BUTTON ON YOUR BROWSER AND THEN FOLLOW ONE OF THE LINKSABOVE TO CONTINUE.

Do not touch places other than thosespecified. Touching places not specified can cause an electric shock orshort circuit accident.

Do not press undesignated key. Pressing any undesignated key can causemalfunction and adjustment fault. Should the key be pressed by mistake,turn power off and turn it back on again.

TOSHIBA PROJECTOR CONTROL PANEL

TOSHIBA PROJECTOR has two different types, i.e., one equipped with the Control Panel and the other without the Control Panel. When adjusting, be sure to confirm the type used.

STATIC CONVERGENCE ADJUSTMENT (With the Control Panel)

During adjustment, should the screenimage be abnormally disfigured due to static electricity and other causes,do not have adjustment status stored, and be sure to turn power off.

Operate the Remote Control towards the PTV screen. If directed otherthan to the PTV screen, the Remote Control does not function.Unless theCONV ADJ SW is ON, remote control operation is not acceptable. At the timeof shipment, the SW is set to ON. If remote control is not accepted, checkstatus of this SW.

Direct the remote control towards the PTV screen and keep the Test Keypressed down for approximately 3 seconds. The adjustment mode should appearon the screen and the screen turns into the green test pattern.

On the screen, the cross pattern and the square frame line will be projected.However, due to the TV mask, the up/down lines cannot be seen.

When initially installing the machine, or when the installation positionis changed, check to see if the Test Pattern is in the central, well balancedposition. If deviated, adjust the green position by using the Adjust Key"up/down/left/right" in the manner so as to improve the balance(L&R, and T&B are approximately equal as shown).

In the normal usage, with green as reference color, red and blue areadjusted. Therefore, skip the above procedure.

Press the R Key of the remote control. The red pattern together withthe green pattern are displayed on the screen. At this time, the frame colorturns into red.

By operating the Adjust Key of the remote control "up/down/left/right",have the center red match with that of green. When red color is superimposedon green color, it seems to be yellow.

Press the B Key of remote control. The blue test pattern is added tothe display on the screen. At this time, the frame color turns into blue.

By operating the Adjust key of the remote control "up/down/left/right",have the center of the blue match with that of yellow. When blue color issuperimposed on yellow color, it seems to be white.

By pressing the WRITING KEY, have the adjustment status stored. Afterit has been stored, the Adjustment Mode is exited automatically, and thenormal mode returns. If the Test Key is pressed down for approximately 3seconds without having the adjustment status stored, pre adjustment statuswill remain.

The R.G.B. Keys have screen display color change functions. Pressingthe key of the color presently shown on the screen causes the color to disappear,therefore, for adjustment, press the key again.

ADJUSTMENT OF TOSHIBA PROJECTOR (THE TYPE WITHOUT CONTROL PANEL)

The Remote Control is used for adjustment of the type without Control Panel. When adjusting the Projector, direct the Remote Control's light emitting portion towards the Projector Screen.

REMOTE CONTROL BUTTONS

AUTOMATIC COLOR MATCHING

The Projector may be subject to color deviations affected by earth magnetism, the building's steel frames, etc. When the Projector is initially installed of the Projector's installation position is changed, have the color matching performed automatically.

Keep pressing the p button (red) for approximately 3 seconds to have the ensuing movements performed automatically.When the green cross pattern movements are finished, similar detection is performed sequentially in order of red and then blue cross movements. After detecting by green, red and blue cross movements, the game mode returns with the color deviation status being corrected

Although very rarely, the TRY AGAIN error display in red may appear. At this time, press the P button (red) for approximately 3 seconds. Even after the above operation is repeated, if the error condition still exists, then display shifts to PLEASE ADJ. In this Case, the auto color matching function can not be used. Contact the place of contact herein stated or where the product was purchased from.

If the automatic color matching indicates an error, color matching can manually be performed. Refer to CONVERGENCE ADJUSTMENT (manual color matching).

ADJUSTING THE ON-SCREEN CONTRAST

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary. Changing the CONTRAST causes the light and shade of the on-screen images to be changed.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure "2" and press the SET BUTTON.

To continue adjusting other menu items, repeat procedure "2~4"

Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will prevail when the power is turned ON the next time.

ADJUSTING THE ON-SCREEN BRIGHTNESS

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary. Changing the BRIGHTNESS causes the light and shade of the on-screen images to be changed.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure "2" and press the SET BUTTON.

To continue adjusting other menu items, repeat procedure "2~4"

Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will prevail when the power is turned ON the next time.

ADJUSTING THE ON-SCREEN CONTRAST

Although the on-screen display position (H. POSI, V. POSI) has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure "2" and press the SET BUTTON.

To continue adjusting other menu items, repeat procedure "2~4"

Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will prevail when the power is turned ON the next time.

ADJUSTING THE SCREEN SIZE

Although the on-screen size (H. SIZE, V. SIZE) has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary.

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure and press the SET BUTTON.

To continue adjusting other menu items, repeat procedure "2~4"

Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will prevail when the power is turned ON the next time.

CONVERGENCE ADJUSTMENT (manual color matching)

To avoid circuitry malfunctioningdue to electrical load increase, never utilize CONVERGENCE ADJUSTMENT (LineConvergence Adjustment in particular) for adjusting screen size changes.

There is no means to restore the Convergence Adjustment data oncestored, to its original state. To avoid changing the screen size by erroneouslyusing convergence adjustment, do not perform the green Line ConvergenceAdjustment.

As such, be sure to perform the adjustment work from this page onward by the Technical staff and the location's maintenance Personnel who are well versed in such adjustment work. In the Static Convergence Adjustments, if satisfactory adjustments can not be performed, do not make another convergence adjustment inadvertently. Contact the office herein stated or where the product was purchased from.To avoid making the adjustment work ineffective, do not press the RESET button during adjustment.

To discontinue adjustment work,keep pressing the TEST button for approximately 3 seconds at the stage beforestoring the adjustment data by pressing the WRITING button.

Should the screen be abnormally disturbed by noise due to static electricity,etc., turn the power off without storing the adjustment data.

Pressing the "up or down" PIC-ADJ button in the ConvergenceAdjustment Mode status will display the Adjustment Menu as this is the oneapplied at the factory.

Adjusting this menu causes the Customer's adjustment range to be deviated.

Should the menu shown right be displayed by mistake, first chooseEXIT by using either "up or down" PIC-ADJ button and then pressthe SET button.

STATIC CONVERGENCE ADJUSTMENT

In the static convergence adjustment, each of red and blue images iscomprehensively moved to and superimposed on the green color. If automaticcolor matching function is not sufficiently satisfactory, perform this adjustment.Be sure to perform automatic color matching before starting the above adjustment.

When either of "2" "4" COLOR SELECT buttons (R,B)is pressed, if the color desired to be adjusted disappears, press that particularbutton again. For example, if the red color needs to be adjusted again atthe stage of "4" the R button need to be pressed twice.

POINT CONVERGENCE ADJUSTMENT

In the POINT CONVERGENCE adjustment, each of red, green, and blue images is partially moved for color matching. The adjustment may be necessary when the Game Board is replaced or changed, or screen size is changed. Be sure to perform automatic color matching before starting.

NOTE 1:

When the MODE button is pressed, the adjustment modes will circulate as follows:

NOTE 2:

When either of the COLOR SELECT buttons (R, B) is pressed, if the desired color to be adjusted is erased, press that particular button again.

NOTE 3:

By repeatedly pressing the SELECT button, only the Projector's TEST pattern screen and the screen superimposing the Game Board Test pattern can be alternately displayed.

LINE CONVERGENCE ADJUSTMENT

In the LINE CONVERGENCE adjustment, the adjustment point of the column line (vertical) or row line (horizontal) is comprehensively moved for color matching.It is convenient to utilize this adjustment when color of the column line row line is uniformly deviated.

NOTE 1:

When the MODE button is repeatedly pressed, the adjustment modes will circulate as follows:

NOTE 2:

When either of the COLOR SELECT buttons (R, B) is pressed, if the desired color to be adjusted is erased, press that particular button again.